can i adjust the amount of h20 or saline to boost a tek ? ( i think i can but i am not sure by how much)

using the max ion , then goosing it up on the h20 side so the aqueous layer will break right at the long neck point of the round bottom flask , which is 2280ml , anything added to the vessel after that goes up into the thin long neck making the extraction very painless . my pal suffers intense back pain . pulling hurts .

the issue is atm my pal only has 100 acrb and he would like to use his pyrex round bottom flask as the extraction vessel .

is adding more saline solution than called for ( 500ml or so ) going to put a wrench in things ?

posted the same simple question three times not a single response ?

Relax, it's only been a couple of hours since you posted. Also your post isn't the clearest.

You can use more saline solution if you wish, it will not hurt. You may want to use slightly more NPS to pull with.

posted 10/25/2018 4:30:26 PM - this may be clearer - i will also share the second post which went without any reply until i "made a stink" , and then i get told to relax - classy .

Hey there , so my pal found a 2000ml pyrex Round Bottom Flask at a resale store . it has a long neck which makes the NPS extraction very easy if the layer would split right at that point where the ball of the flask blooms into the very narrow stem .

the measurement of the ball alone is 2280 ml .

the complete measurement of the entire flask is 2390ml .

looking at this thru noob eyes , a 50g cyb salt tek comes out to 690ml , a 50g max ion can also hit 1590 , those numbers added = 2280 . 2280 is perfect amount minus nps as 2280 would fill the round flask completely to the brink where the narrow stem starts , that is where the nps would dit making the extraction process a breeze .

ultimately my pal is looking for an adjusted tek utilizing 100g acrb to hit 2280 . he states this is silly , mixing these two separate teks into a single vessel and would rather perform the tek at one single swipe and hit this magic number of 2280 minus the nps . ideally utilizing just 100g acrb , but again he is not experienced enough to understand if one can merely just add 500 ml more water to a 50-100g ab atb and not suffer any consequences .

he calculated a single max ion that came out to something like 1800ml , and then added additional a total of around 500ml h2o -like 100 at the initial acrb mix and then an additional more significant amount of 400 ml additional h20 (and salt) added at the salting stage . he claimed at this point he felt he was straying too far and that he would be putting the project at risk .

i know it seems like throwing the baby out with the bath water but he claims the extraction process utilizing this sort of vessel to be night and day . he is being very stubborn . i am not sure what to tell him and he was not willing to sign up here so i am here asking for assistance in his sted .

he is currently attempting to obtain some long neck 1500 ml vodka bottle , and looking at resale stores , he found a 750 ml liquor decanter long neck bottle that would work for a single 50b cyb salt , or perhaps considers splitting a 100g max ion into two separate pulls using this smaller vessel which i am thinking would be a hassle
.

aware of the 1:15:1 rule of thumb.

question - CAN my pal use moar h20 in a tek ?

comparing the cyb salt tek to the max ion tek it appears the ONE difference is in the amount of h2o used in the salt stage . its 1 liter vs 100 ml .

in his case he would be trying a max ion and using more h20 . around 100ml or so more , simply as the extraction vesel works much better at this amount . he has obtained several types of flasks with long necks , so he is trying to taylor his teks to hit the number where the flask works best ie layer is equal to flask volume nps sits in the long neck portion , dig ?

lets say he is starting with 50g acrb and then using 400ml , but at the salt stage running it higher at 1100ml would this be "bad" and why ?

as far as why its in a another thread called " pyres love affair" which may have been too wordy . he found a smaller flask which is around 1830 , where the long neck starts so he is thinking he will be ok going water heavy . perhaps he should consider using 100g of acrb ?

a huge thanks to anyone who would help me out with info . i am hoping to figure out how to adjust a tek to use the 2280 ml flask , that will run up to 2390 full and it would work very well

TL;dr is it cool to use moar water in a tek ? or no ? why ? ty

being told to relax and then called out for "not being the clearest"

here is something interesting that i stumbled upon :

" From a self-destructive miserable existance I found a life of love and learning through my DMT experiences. I enrolled part time at university to study chemistry, and my life has changed beyond almost all recognition. Perhaps I will write up my story to post here one day.

I would never have come so far so quickly were it not for the incredible wealth of information contained within this website. I am eternally grateful to be a part of this incredible journey. Thank you so much, truly! I only hope I can give back half as much as I have recieved. "

while i am relaxing here i have time to consider my experience in forums . running into folks who would rather tear each other to pieces , treat others like dirt , mock them ignore them .

i had hoped for something different here .

change my mind ?

You are a disgusting person. I simply explained the reason why no one else was bothering to reply to you in this thread, and still gave you help. At no point did I call you out or attack you, but if you want to feel like you've been attacked then go ahead, that speaks volumes about your mindset and perception of the world (I don't remember telling someone to relax equating to being called out? That's some funny logic that I don't know how you've managed tio arrive at). I had not seen your other posts, I had only seen this one thread you made and I replied with the answer you were looking for, did I not? But you completely ignored that, how convenient.

Don't expect to be welcomed by anyone else on these forums with an attitude like that.

Why would I want to change the mind of someone who chooses to attack the person that tries to help them, just because I hadn't seen the rest of your posts when replying to this thread? Not happening.

Cya

FWIW I think you should be banned for your attitude, BTW.

Perhaps OP should take some time to read through our attitude page.

https://wiki.dmt-nexus.me/Attitude_Page