https://youtube.com/watch?v=EZWdH7mEFnE

Is this a good tek? It seems like the easiest but im concerned since the teks on here are much more complex..
Which tek would u recommend to me? A newbie 1st time extract

Thanks for the help

Imho u shouldn't really have to follow a tek. Before you attempt an extraction you should make sure you understand the reason for every step. It's really not that hard and patience is a virtue.

These are the steps for a basic a/b extraction
First you have to get the dmt out of the mimosa. This goes quicker in a warm acidic enviroment. So if for example you wanted to extract 100 grams i would boil them 3 times for 2-4 hours in 2 liter water and 1 liter vinegar (these are large amounts of water because i like to make sure i get everything) . Then you filter and combine all the (normally reddish) water and reduce the 9 liters down to 1 liter.

DMT naturally occurs as a salt. However, as a salt it will not disolve in your apolar solvent (naptha) so we need to convert it to a freebase (free - base) molecule. Only thing we have to is adjust our ph. it should be close to 12. this can easily be done by using sodium hydroxide or any other base like sodium bicarbonate (thats a weak base tough).

After adding enough base, the dmt will easily disolve in a apolar solvent. This is your naptha/limone/most other pure apolar hydrocarbons are ok. add 1/3 solvent to your total volume of water, and shake it gently for 10-15 minutes then seperate the upper layer from the bottom. Again do this 3 times and combine your solvents, then you let it evap with a fan at room temperate untill you see little white crystals forming. Then put it in the freezer overnight, quickly take it out and pour of your solvent, the crystals will remain and then you airdry the remaining solvent

If you used enough base this method should have 100% succes rate. if you have any questions i'll do my best to answer them
Good luck with your hyperspace travels.

These amounts are over the top IMHO esp the naphtha , also IMHO I use Cybs salt TEK all the time , it's super easy , quick , clean efficient , and high yeilding , also has pics for greater understanding !

Do not listen to this muppet , " the brown stuff is dust " but " the brown stuff is good dmt "

What a total clown ! IMO stay away , far away from this dude omg lol

Cyb,

I'm a newbie and I have mainly been researching stb teks. What is the advantage of the acidic bath and the addition of salt in your tek? I'm presuming higher yields but why is this?

Thanks
Woody

I no that stb yeilds less especially when using acacia bark , but the salt after the adidifying stage helps push out the dmt within the first six or so pulls ! The advantage of the max-ion TEK which is the same as the salt TEK except for the freeze thaw x 3 and a longer acid soak , it helps lyse the walls of the cells to help break them down !

I think that's correct !

Ok gotcha. Should i use mhrb bark or powdered at first? Mod edit: No sourcing talk

Sourcing talk is against the rules. You should read the attitude page if you haven't.

sigh... Youtube tek?! seriously?? That's a good way to enlighten the masses on the wonders of DMT... I hate seeing things like this on youtube.

He could have at least done it properly lol

Lev... Come on man. I've known you for like 20 minutes and I can't count the rules you've broken. I don't suppose this youtube tek is against the rules, but... sigh.

Come of the grass lev8177 ,, why on earth would you think we can just break rules and it'll be ok ,,

Truely you're not showing any effort into researching and studying any of the TEKs YouTube doesn't count , and if you were to follow that goose you're sure to fail !

I'll give you advice that is of most importance to you , Research is key !

I also see your've made 4 posts , you're 1st post should've been an introduction of you'reself so we get a feal for the person you are , but all you've done is asked to be spoon feed ,

lol youtube the only good teks on there is for mushrooms and san pedro tea

…is an unnecessarily large amount of vinegar to use. It will stink. It will make basifying harder. ~1tbsp 5% vinegar per litre H2O will get you down to a suitable pH.

Yeah, I don't trust much things off of youtube. Its being blatantly lied to or told inadequate info by the one that posted it...

Research is good to do friend. Plus you come across some cool stuff you never even knew about as well sometimes!

Namaste,
---dls---

Ugh, I just watched the video. It is dangerous and the comments are full of confusion and misinformation.

Please — at least wear gloves and eye protection, keep some vinegar close and easily accessible to neutralise spills.

As said before, YouTube is not the place to get advice on things like this. We have an incredible resource here — so much knowledge, a better class of contributors, clued-up people to save people from themselves. Why go anywhere else?

I quit watching as soon as I saw the title... you don't "make" DMT; you extract DMT.

Simply showing someone the errors of their ways is enough, no need to put someone down for not having done the research or read the forum rules.

I read a few teks many many times before i chose the right one for me. First things first, which extraction chemicals are accessible to you, then go from there.

Indeed, and it shows intelligence asking this question:


I am sure most who see that tek on YouTube won’t bother searching for further advice after.

While it is good to educate it is not good to scare new members of our community off when asking perfectly good questions! Everyone deserves a chance.

Another vote for Cyb's salt Tek. Pure and easy.

The D-Limonine food safe tek is also very good.

Firstly, read through the FAQ, familiarize yourself with the basic chem terminology, even use the google wiki to learn basic terms if need be, then go from there.

Even go to google, type in a set of keywords or your question, then type 'dmt nexus' after that and most if not all your answers will come up. It works really well ime.

Cybs tek is great, so is nomans stb tek, etc. Just take your time, learn the terminology, research throughout the forum thoroughly. This can take weeks, or even months, before your actually able to nail a tek down, get the materials necessary, etc - it's a journey in and of itself. Read, read , read. Ime, reading and learning step by step and not being in a rush will pay off in the long run.